Green is the applicable area, red is the inapplicable area, the diameter of the dent area must be greater than 2cm to be applicable.

Buyers Must Know

1. The paint on the dents is damaged, scratched, or waxed or coated. it is not recommended;2. The dent is too small, and the suction cup is not in contact with the concave surface enough, resulting in insufficient adhesion of the glue and easy degumming, and this tool cannot be used;3. The depression is not iron sheet, it is steel plate or plastic. The depression is in particularly hard places such as the body beam. It is recommended to go to the repair shop for maintenance;4. The alcohol bottle in the package is empty and does not contain alcohol, because alcohol is a prohibited transportation item;5. Please use alcohol or diesel with a purity of 95 or higher to remove the glue from the car surface.6. The applicable temperature of the glue stick is 0-40 degrees Celsius. If in winter, the hot melt adhesive may solidify quickly and fail to stick. At this time, you can use a hair dryer to heat the bonding area.

Long T is a labor-saving drawing method, it is convenient and effective to repair large and small dents；Short T is a laborious drawing method. It is easier and faster to repair small dents with your own strength.

Package Lists

Using Methods

Step 1 :Clean the dent with a clean wet cloth;Step 2 :Mount the glue stick into the glue gun,pull the trigger to let the glue stick enter into the glue gun, connect the power source and preheat for 3-5 minutes;

Step 3: Use a proper drawing gasket. Large dent requires a large drawing gasket. (Note: The larger the drawing gasket is, the larger the drawing force is);Step 4: Use a glue gun to apply glue evenly on the selected gasket, with a little more glue in the middle;

Step 5: After the glue is applied, quickly stick the suction cup into the recessed position. Be sure to lighten it when pasting. Don’t squeeze the glue to the outside. When the glue cools quickly, there is a little residual temperature, and the adhesion strength is the largest;Step 6: Pull the main sucker of the T puller head card. It must be kept vertical and pulled out. Do not use too much force. Repeat the operation several times until the depression is flat;

Step 7: After repairing, use hot water above 80 degrees and scrape while pouring, the glue will become soft, and then clean it with a shovel, and finally spray alcohol to remove the remaining glue, and you are done.

The Last

If the above steps are not successful, please repeat the operation.If there are raised spots on the surface after repair, please follow the steps below:1. Press with your thumb until the raised point is flat;2. If the pressing cannot be repaired, use a leveling pen to align the raised points, and gently tap with a rubber mallet, repeat several times until the repair is smooth.

Size and Details

Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.

Common problems:

1. Insufficient heating of glueFully heat for 5-7 minutes, until there is liquid from the muzzle or press the switch lightly, the glue will be released2. The glue is too little and too thin on the gasketIt needs to be even and thick, and you can apply a little more in the middle, and quickly stick to the recessed area after applying3. Wrong pulling directionWhen pulling, it should be as vertical as possible to the body4. Too much pulling forceShould be uniform and moderate, repeat the operation many times5. Too much force to stick the suction cupToo much force will easily squeeze the glue to the outside, you should press gently for 2-3 seconds6. Pull time issuesAfter the suction cup is attached, pull it when the glue cools down and there is residual temperature. The temperature of the sol is too high or it is completely cooled before pulling it, it will easily fall7. The suction cup is very easy to fall off because of floating dust or water on the surfaceThe sunken area should be washed with water and dried with a towel8. The car body temperature is too high in summerUse cold water to cool the recessed area first, and then dry the water9. The car body temperature is too low in winterFirst heat the recessed area with hot water, and then dry the water10. sucker size problemThe larger the suction cup, the greater the suction power, which is suitable for the flat and concave area

Important:

Due to the difference in the heating time of the adhesive strip and the thickness of the application, it may fall off in one operation, so you need to be patient and repeat the operation several times! ! You can also experiment with other things to determine whether the glue is sticky! !

Is the residual glue not clean?

1. Use high-concentration alcohol to clean up with a spatula while spraying (diesel, gasoline and asphalt can also be tried)2. Use a hot air blower to heat the glue, and then clean it with a spatula3. Use hot water above 80 degrees Celsius to clean up with a spatula while pouring it